Last month I finally found the time to finish one of the DIY projects I’ve had on the go for months. The project was turning a Sony Walkman into a nasty distortion box and I’m really happy I finally finished it.
The concept is simple. Remove the mechanical guts, replace jacks and overload the Walkman amplifier to create distortion. It’s not a tape distortion but I can do that in a different project. Any portable cassette player will work. I like the Sony Sport for it’s great rugged case and memorable look. A player with EQ controls, bass boost or other enhancements could be helpful.
Step 1 – Remove guts
Remove the tape mechanism, tape head, radio antenna, and extra plastic parts. Take note of where the tape head attached to the board and points that the play switch connected.
Step 2 – Power
A power supply is needed for testing and it should be removed before any soldering. Batteries heat up fast! Attach the power with alligator clips to the circuit board. Solder the play control points to the on position to keep the power always on. Solder a switch on one of the battery leads to cut power.
The most difficult part of the build was creating a battery holder for the two AA. Several hours of trial and error went by before I found a reliable solution. If you attempt this project I recommend buying a AA battery holder because they’re very tricky to fabricate.
Step 3 – Solder Jacks
Replace the 1/8″ TRS jack with 1/4″ TS jack. Simply desolder the jack, run leads into the board from the jack.
The input jack replaces the tape head. I soldered right to the legs of the opamp. If you connect the ground first, you can just poke around with the hot lead until input reaches the output. This is a good way to troubleshoot or experiment. I also removed the volume control pot and shorted it to full volume.
Step 4 – Test and experiment
Now that you have the power, input and output connected, run some sounds through it. Mine did very little with a guitar connected directly to it going to a small passive speaker. Taking a signal from my audio interface in gave me plenty of level to work with, in fact I could drive a 8ohm 12″ speaker at a healthy level. This is a good time to try circuit bending. I kept things pretty simple and just added a switch to bridge the channels for increased gain.
Step 5 – Mount jacks and switches
Get the circuit board back in the case and figure out where there is room to safely drill a few holes for jacks and switches. Drill, trim, reassemble, done.
Reamping a monotron through a walkman. Distortion! vine.co/v/bgY0EFVIJVl
— Jon Tidey (@theaudiogeek) February 26, 2013
In the example clips below I recorded some sounds out of my Korg Monotron Duo then reamped the audio through the Walkman distortion.
I am very happy with how this turned out and is a very usable effect for some sources. I think it works particularly well for dirty synths like the Monotron. The entire build would have been much faster if only I had that battery clip. You could probably do this in under an hour if you don’t get carried away with testing and making noise like I did.
What do you think of this project? Is this something you would build? Do you want to hear examples of it on other sources? Let me know in the comments!
Hi Jon, interesting project indeed. Too sad that I just threw away my broken Away walkman a couple of month ago after keeping it for years. It was a nice one with a stable metal casing. Would’ve been challenging to put all the big jacks into it, but there would’ve been a way. Especially the fact that you can drive a speaker with it sounds great. If I get you correctly you connected a (passive?) guitar directly to the input and the resulting level was too low? Seeing this walkman more like a power amp you could just insert a guitar pedal ((treble-)booster, overdrive, distortion) and feed that into the wm. This should work and then keeping the volume control would be helpful for adjusting either the volume for a speaker or the gain/distortion the little toy produces. One question: if the signal is hot enough to drive a speaker, wouldn’t it be good to use a DI box for connecting it to the audio interface? Otherwise you could smoke your audio interface’s inputs, right? The DI box would allow you to attenuate the signal for safety reasons… If you find time to record a guitar with a pedal (through a speaker?) this would be nice. I need to watch out for a broken walkman now… 😉
[…] DIY Walkman Distortion Effect […]
Great job Jon! I love the idea of re purposing technology. Reading this made my morning 🙂
[…] (which – OH MY GOD – is currently featuring an article about running synths through an overdriven walkman), and Epic Sounds (his recording, mixing and mastering […]
[…] DIY Walkman Distortion Effect […]