Press "Enter" to skip to content

3 Mid-Side Processing Tricks

In this article I’ll explain how I use Mid-Side processing on stereo sources for practical or creative effects.

Mid-Side?
Two channels of audio can be combined in a way that gives us control over what is the same in each signal, the middle, and what is different, the sides. The middle is where the kick drum, snare, bass, vocals and a lot of other instruments are, the sides have any hard-panned instruments and spatial effects like reverb. It can be pretty interesting to listen to music like this, there can be a lot hidden in the side channel.

MS is also a stereo microphone technique using a cardioid microphone facing the source and a bidirectional mic turned 90 degrees away just picking up ambience. In this situation the two signals would need to be decoded into stereo. The side mic signal is duplicated, polarity inverted and the two side signals are then panned hard left and right. This is not a true stereo mic technique but can sound very nice. The balance of mid and side signals can be adjusted as needed by changing the level of the 3 tracks.

You can manually encode and decode stereo files to MS and use mono plugins to process mid or side individually. A lot more plugins have an MS mode now. Many of the modules in the T-Racks suite allow mid side processing, as does Ozone, a few compressors and equalizers and a distortion also come to mind.

You can do this for subtle or crazy effects, its a fun way to experiment with plugins and get some unique sounds.

Loud and wide
For a recent mastering job I used a Fairchild compressor plugin in MS mode (Lat/Vert) to compress the middle and increase the level of the sides. I did this in parallel so I could blend the effect in easily. I was also using this to get a lot of extra loudness. You can call this parallel MS Compression.
Compare the master without the parallel MS compression, then with, then the parallel compression soloed.
[audio:http://audiogeekzine.com/wp-content/uploads/mid_side/TS_master_A.mp3|titles=Master A (no MS)]
[audio:http://audiogeekzine.com/wp-content/uploads/mid_side/TS_master_B.mp3|titles=Master B (with effect)]
[audio:http://audiogeekzine.com/wp-content/uploads/mid_side/TS_master_C.mp3|titles=Master C (effect soloed)]

Parallel Mid-Side Compression with Fairchild

No more messy verb
I had someone ask about clearing up the middle of a mix when using a lot of reverb. Using Mid-Side Compression on the reverb return can work well. Compress the middle more than the sides and increase the side volume if you want more width.
Here is an example of that on some drums. The drums are Steven Slate playing in KONTAKT. The whole kit is sent into Valhalla Room. With the Fairchild after the reverb I’m lowering the middle by 2dB and raising the sides by 2.

Here you can listen to this effect with lots of reverb on the drums.
[audio:http://audiogeekzine.com/wp-content/uploads/mid_side/drums_wet.mp3|titles=Drums Wet (no MS)]
An now with MS compression on just the reverb bus.
[audio:http://audiogeekzine.com/wp-content/uploads/mid_side/drums_wet_MS.mp3|titles=Drums Wet (MS compressed verb)]
There is NO compression on the drums themselves, I’m only compressing the reverb return and widening it.

Wacky effects
Here is an example of what you can do with a stereo loop and any plugin. This is a little more complicated, and only works if there are hard panned sounds. The loop I started out with had a hihat that wasn’t panned very hard, I copied it to a new track, filtered out all the lows, boosted some highs and then panned it hard left. I recorded the combined original and panned track to a new file.
Here is what I’m starting out with
[audio:http://audiogeekzine.com/wp-content/uploads/mid_side/Loop-dry.mp3|titles=Loop Dry (no MS)]

Now that I had something on the sides I could mess around with Mid Side Processing.
The first thing you have to do is convert Left – Right to Mid and side. I use the free +matrix MS decoder from SoundHack.com. After that I used a delay plugin to add some filtered echoes just to the middle by disabling the right side input.
In the next insert I used a distortion on just the right side. This brought out a lot more of the reverb than was heard in the original loop. Lastly,  second MS decoder was used to bring it back to stereo.

Soundhack +matrix MS encoder/decoder

Here is how the loop sounds now with delay in the middle and distortion on the sides.
[audio:http://audiogeekzine.com/wp-content/uploads/mid_side/Loop-MS.mp3|titles=Loop with MS effects]

Pretty cool right!? I hope you have found these tricks useful.

8 Comments

  1. Christian Coriolis
    Christian Coriolis January 25, 2012

    Very nice post. I like creative use of stereo techniques like that – it’s more fun (and often sounds better) than just piling on effects till you turn green in the face.

    • Nick Lewis
      Nick Lewis January 27, 2012

      I use mid/side for mastering all the time – worth mentioning that running some plugs in linked mid/side mode (like compressors) can keep the stereo image tighter than in standard left/right.

  2. […] Jon Tidey: I used a delay plugin to add some filtered echoes just to the middle by disabling the right side input. In the next insert I used a distortion on just the right side. This brought out a lot more of the reverb than was heard in the original loop. […]

  3. Thomas Mrak
    Thomas Mrak February 24, 2012

    Thanks for the tips!

    Been having a hard time wrapping my head around mid-side processing. This helps immensely.

    Nice to see people using REAPER more often!

    • Jon
      Jon February 24, 2012

      Hi Thomas, thanks for commenting.
      You might also like my other blog –

  4. Sam
    Sam June 11, 2013

    I use mid/side a hell of alot, Its a great way to really tighten the bottom end and get a wider top end. Iv done some mastering for Vinyl recently and its a good way to also mono some of the lower end too keep that punch and things in the center if used correctly…

Leave a Reply

Your email address will not be published. Required fields are marked *